爆炸荷载作用下钢筋混凝土防爆墙动力响应研究

为了研究钢筋混凝土防爆墙的抗爆能力,采用有限元分析方法对不同纵向配筋率、不同高跨比、不同厚度的墙体在爆炸动态荷载作用下的动力响应进行研究,对各种不同设置的钢筋混凝土防爆墙的抗爆性能进行评估。结果表明:减小高跨比对提高钢筋混凝土防爆墙的抗爆能力最为重要,提高纵向配筋率,增加厚度都能增加防爆墙的抗爆能力。     

济南市道路扬尘排放因子估算及其影响因素研究

以济南城市道路为研究对象,采用美国环保署AP-42模型和方法,通过道路分类、优化布点、样品采集、实地观测和计算分析,获得道路粉尘负荷及四种类型道路扬尘的排放因子,探讨了排放因子的主要影响因素。结果表明,路面粉尘负荷随车流量增大而逐渐降低,城市城区路面粉尘负荷多小于城市外围路面,且外围道路路面粉尘负荷随时间和空间变化大;支路和次干道排放因子相对较小,快速路排放因子较高,主干道排放因子最高,其TSP、PM10、PM2.5排放因子分别高达25.239 3 g/VKT、4.731 1 g/VKT、0.597 2 g/VKT;排放因子随平均车重增加呈现逐渐增大趋势;同种类型道路排放因子均随道路粉尘负荷的增加而增加;次干道和快速路排放因子随车流量增大而减小。所获结论可为城市道路扬尘排放估算提供参考。     

重庆三峡库区非点源污染评价与影响因子分析

选取重庆三峡库区4个行政建制镇进行非点源污染监测与调查,以COD、TN、TP、Cu、Zn等指标为主要研究内容对库区农村环境进行污染特性分析并且利用等标污染负荷法对其生活污水、生活垃圾、畜禽养殖、水产养殖、化肥流失、农药流失、水土流失等污染源进行非点源污染评价。结果表明:COD、TN、TP、Cu、Zn的平均排放浓度分别为22.15 mg/L、6.37 mg/L、1.49 mg/L、47.73 g/kg、85.24 g/kg,库区主要污染物依次为TN、TP、COD、Cu、Zn等,主要污染源依次是畜禽养殖、化肥流失、生活污水、生活垃圾、农药流失、水土流失、水产养殖等。采用SPSS软件对影响库区环境污染的季节、收入水平、地域、畜禽养殖规模、环境基础设施完善程度等因子进行了分析,结果显示:COD主要影响因子是地域和畜禽养殖规模,TN主要影响因子是季节、地域和畜禽养殖规模,TP主要影响因子是环境基础设施完善程度、畜禽养殖规模和地域,Cu、Zn主要影响因子均是畜禽养殖规模。该研究可为重庆三峡库区生态修复、城乡统筹下的城乡规划及产业布局提供理论基础。     

Performance of the hybrid growth sequencing batch reactor (HG-SBR) for biodegradation of phenol under various toxicity conditions

Hybrid growth microorganisms in sequencing batch reactors have proven effective for treating the toxic compound phenol, but the toxicity effect under different toxicity conditions has rarely been discussed. Therefore, the performance of the HG-SBR under toxic, acute and chronic organic loading can provide the overall operating conditions of the system. Toxic organic loading(TOL) was monitored during the first 7 hr while introducing50 mg/L phenol to the system. The system was adversely affected with the sudden introduction of phenol to the virgin activated sludge, which caused a low degradation rate and high dissolved oxygen consumption during TOL. Acute organic loading(AOL) had significant effects at high phenol concentrations(600, 800 1000 mg/L). The specific oxygen uptake rate(SOUR) gradually decreased to 4.9 mg O_2/(g MLVSS·hr) at 1000 mg/L of phenol compared to 12.74 mg O_2/(g MLVSS·hr) for 200 mg/L of phenol. The HG-SBR was further monitored during chronic organic loading(COL) over 67 days. The effects of organic loading were more apparent at 800 mg/L and 1000 mg/L phenol concentrations, as the removal range was between 22%–30% and 18%–46% respectively, which indicated the severe effects of COL.     

深圳宝安区土地利用变化的环境影响研究

采用深圳宝安区1996-2004年的土地利用数据及其逐日降雨量资料，应用Costanza关于生态系统服务价值方面的研究成果，对该区域土地利用变化导致的生态服务价值进行了计算；应用SCS模型对该区主要污染物氨氮（NH4-N）、总磷（TP）以及高锰酸盐指数（CODMn）的面源污染负荷的变化进行了定量分析。结果表明：1996～2004年期间，土地利用变化导致区域总体生态服务功能下降了31．36%；氨氮和CODMn的面源污染负荷分别增加了4．12%、5．73%，总磷的面源污染负荷减少了1．64％。进一步对三种土地利用规划供选方案（2004-2020年）的环境影响进行了分析。在不同规划方案下，到2020年，宝安区总体生态服务功能将比2004年下降3．79％、10．97％和30．76％。但其下降速度都将得到明显遏止；氨氮、总磷和CODMn的面源污染负荷也将有较明显的增加，且皆以规划方案1增加最小,方案2居中，方案3增加最大。     

Reconsideration on the effect of nitrogen on mixed culture polyhydroxyalkanoate production toward high organic loading enrichment history

Effect of nitrogen on mixed culture PHA production was reconsidered. Enrichment history of PHA accumulating culture was discussed. Higher PHA content and biomass growth were achieved in presence of nitrogen. Enrichment strategy toward higher PHA accumulation was investigated. Microbial community succession in PHA accumulation phase was investigated. In most of the operating strategies for mixed microbial cultures polyhydroxyalkanoate (PHA) production, moderate organic loads and low nitrogen concentrations are used, however, the real waste streams contain variable concentrations of carbon and nitrogen. To evaluate the effect of enrichment history on PHA producer and production the various carbon and nitrogen levels were utilized during the accumulation phase. Different operating strategies were applied in three sequencing batch reactors (SBRs) subjected to aerobic dynamic feeding. The maximum PHA production of the enriched cultures under nutrient excess, limitation and starvation (Cmol/Nmol ratio of 8, 40 and ∞, respectively) was evaluated in batch assays. A higher PHA content and biomass growth were achieved in the nutrients presence in comparison to the nutrient starvation condition. The cultures from the SBR treated under short sludge retention time, high organic loading rate, short cycle length (SBR#3) and nutrient excess reached the maximum PHA content (54.9%) and biomass increase (38.9%). Under nutrient limitation, the negative biomass growth was observed under nutrient starvation because of the sampling loss. The succession of microbial communities in SBRs and batch assays was analyzed using terminal restriction fragment length polymorphism. The SBR#3 had the best overall PHA production performance considering its high PHA content and productivity in all nutrient content, it indicates that nitrogen has a substantial impact on PHA yield especially when high organic loading rate enrichment history is involved.     

加轴压卸围压下含瓦斯煤岩损伤变形的能量演化机制

采动影响下含瓦斯煤岩的损伤变形是一个极其复杂的非线性过程，单纯依靠传统经典弹塑性力学无法准确分析其破坏机理。针对此情况，通过试验研究了不同初始围压条件下含瓦斯煤岩的损伤变形特征，并分析了损伤变形与能量演化规律之间的内在联系。研究表明:初始围压越高，煤样破坏时强度越大，脆性破坏特征越明显，瓦斯流量急剧增加幅度越大，煤样破坏时积累的总能量和弹性应变能越多，且初始围压与弹性能之间满足对数函数关系。采用累积耗散能定义了煤岩损伤变量，并分析了不同阶段损伤与渗透率之间的演化关系。     

Validation of a booted finite element model of the WIAMan ATD lower limb in component and whole-body vertical loading impacts with an assessment of the boot influence model on response

Objective: A novel anthropomorphic test device (ATD) representative of the 50th percentile male soldier is being developed to predict injuries to a vehicle occupant during an underbody blast (UBB). The main objective of this study was to develop and validate a finite element (FE) model of the ATD lower limb outfitted with a military combat boot and to insert the validated lower limb into a model of the full ATD and simulate vertical loading experiments.

Methods: A Belleville desert combat boot model was assigned contacts and material properties based on previous experiments. The boot model was fit to a previously developed model of the barefoot ATD. Validation was performed through 6 matched pair component tests conducted on the Vertically Accelerated Loads Transfer System (VALTS). The load transfer capabilities of the FE model were assessed along with the force-mitigating properties of the boot. The booted lower limb subassembly was then incorporated into a whole-body model of the ATD. Two whole-body VALTS experiments were simulated to evaluate lower limb performance in the whole body.

Results: The lower limb model accurately predicted axial loads measured at heel, tibia, and knee load cells during matched pair component tests. Forces in booted simulations were compared to unbooted simulations and an amount of mitigation similar to that of experiments was observed. In a whole-body loading environment, the model kinematics match those recorded in experiments. The shape and magnitude of experimental force–time curves were accurately predicted by the model. Correlation between the experiments and simulations was backed up by high objective rating scores for all experiments.

Conclusion: The booted lower limb model is accurate in its ability to articulate and transfer loads similar to the physical dummy in simulated underbody loading experiments. The performance of the model leads to the recommendation to use it appropriately as an alternative to costly ATD experiments.     

不同混凝剂处理松花江低温水

东北松花江地区冬季有将近6个月的冰封期,低温季节水源水处理难度大。为了保证东北地区冬季饮用水供应,研究几种混凝剂在处理冬季松花江低温水时的混凝效果。实验结果表明,NPAC1和NPAC2水解产物中具有较高的Alb和Alc成分,拥有较高的电中和、吸附和网捕卷扫性能,高效聚铝铁(PAF)水解产物Fe(OH)3具有比表面积大、吸附架桥作用较强的优点。这3种混凝剂无论是在控制出水浊度还是在对水体有机物去除能力方面均优于目前水厂所使用的PAC和聚合氯化铝铁(水厂PAF);NPAC2的投加量达到50 mg/L时,出水浊度达到最优;当混凝剂投加量达到50 mg/L时,NPAC1的浊度去除率逐渐超过NPAC2,剩余浊度低于3.0 NTU;NPAC1、NPAC2和PAF 3种混凝剂对有机物的去除能力大致相当,当混凝剂投加量为50 mg/L时,这3种混凝剂处理后的水的UV254的值均低于0.06,而水厂使用的2种混凝剂处理后的水的UV254仍高于0.1;结合其对浊度去除的情况,可以判断55 mg/L的投药量为NPAC1的最优投药点,PAF的最佳投药量为65 mg/L;投加适量的粉末活性碳可以有效地提高氨氮的去除率,当粉末活性炭的投加量为30 mg/L时,氨氮的去除率基本达到最大(51.27%)。表面负荷对混凝效果具有重要的影响,合理降低沉淀池的表面负荷对于提高出水水质具有重要作用。     

加载条件下原水管道受力特征模型试验研究

为研究堆载大小对原水管道受力变形的影响,采用量纲分析法得出模型试验相似比,并根据相似比进行模型箱的设计、管道材料的选取和重塑土的配制,研究不同工况下管道的受力特征。试验结果表明:整体上管道端部应力大于管中央应力,管轴向应力大于管环向应力。在中心加载下,管端应力值较管中央处大,前者增长速度更快,而后者增长速度较慢。在偏心荷载作用下,靠近荷载的管端应力最大,而管中央应力最小;尤其在偏载6 kPa作用下,管端下表面轴向应力达到595 kPa,而管中央处仅有64 kPa,管端受边界约束作用明显,管道呈弯曲变形。